Specimen (Sample) Preparation Equipments

The mounting press is a mechanical type machine. By turning the hand-wheel of the machine, a coupling of bevel gear is rotated to drive the screw rod which in turn pushes/pulls the lower die up and down along the mould sleeve. The thermoset plastic granules together with specimen being mounted is formed under heated conditions. During this process the pressure is self adjusted by a spring fixed inside the machine.A signal light is used to indicate the pressure level.

ABQ2B‐50 This Machine is Automatic Mounting Press for metallographic specimen. It is suitable for all Thermosetting Materials, because of the cooling system. It can automatically finish with the heating temperature, the holding time and acting force. The operator can change 4 specifications patterns according to the difficult specimens It can make 2 specimens at one time.

BETAMON-5automatic metallographic specimen mounting press is a kind of full automatic mounting press, equipped with in-out water cooling system.

BSQ-80 Metallographic specimen cutting machine can be used to cut various metal and non-metal materials so as to get specimen and observe the metallographic or lithofacies structure. It has cooling system so as to clear up the heat produced during cutting and avoid to burn the metallographic or lithofacies structure of specimen because of superheat. This machine features easy operation and reliable safety. It is the necessary specimen preparing instrument for using in factories, scientific research institutes and laboratories of colleges.

Our BGE-100S Manual / Automatic Metallographic specimen cutting machine can be used to cut various metal and non-metal materials so as to get specimen and observe the metallographic or lithofacies structure. It has cooling system so as to clear up the heat produced during cutting and avoid to burn the metallographic or lithofacies structure of specimen because of superheat. This machine has stainless steel machine body and worktable, and it features easy operation and reliable safety. It is the necessary specimen preparing instrument for using in factories, scientific research institutes and laboratories of colleges.

This Machine is Automatic Mounting Press for metallographic specimen. It is suitable for all Thermosetting Materials, because of the cooling system. It can automatically finish with the heating temperature, the holding time and acting force. The operator can change 4 specifications patterns according to the difficult specimens It can make 2 specimens at one time.

Metallography Specimen Grinding & Polishing Machine

BETAMON-7 Automatic Metallographic Specimen Mounting Press is a kind of advanced full automatic mounting press, the whole process of mounting can be controlled by program, and realized one-key operation for process of mounting, includes heating, pressuring, dwell of pressuring, cooling, release of pressuring, etc. It suits to mount the specimen of metal and rock.

Our BETACUT-5Precise Cutting Machine can be used to cut non-metallic material, circuit board, semiconductor, super hard material etc.The cutting precision can reach 0.01mm.The machine is equipped with many jigs, which make it possible to cut samples with irregular shape. It is an ideal precise cutting machine for the scientific research institutes and industrial enterprises.

ACO-50(A) Automatic Metallographic Specimen cutting machine is equipped with big cutting room and movable work table. Therefore, this machine has the ability of cutting large specimens.

50Abrasive Cutting Machine is rugged, sturdy and designed to cut metallurgical samples to optimal quality consistently and safely. Cutting wheel mounted on the spindle to get the optimum output of the motor.

Our ACO‐200 Heavy Duty Metallographic Abrasive cut‐off machine can be used to cut various metal and non‐metal materials so as to get specimen and observe the metallographic or lithofacies structure. It has built in cooling system so as to clear up the heat produced during cutting and avoid to burn the metallographic or lithofacies structure of specimen because of heat.

MAIN FEATURES: Pneumatic drive to load  Rotate speed display in digital  Force and sampling time changeable  Polishing disk with two steps stationary speed and step less speed control  Polishing principal axis with stepless speed changed  With nice and durable ABS crust and stainless steel current pieces, rustless forever. Quick change polishing disk design,variable specimen holder  Central force  Large volume abrasives automatically dispensing system  Preparing for several samples simultaneously

Metallography specimen polishing machine is a kind of double disk table type polishing machine and can be operated by two persons at the same time. It is suitable for the polishing & grinding of the specimen. The specimen surface is very smooth after processing and can be used to observe and measure the metallography structure of specimen under microscope.

Model DBC-150 Low speed precise specimen cutting machine is suitable for the precise cutting of various hard materials. It is especially suitable for the precise cutting of all kinds of small metal, non-metal pieces and various electronic components. This machine can be equipped with diamond saw blade and other resin blade so as to meet the demands of cutting of various specimens.

Model BC-100B Automatic Metallography specimen cutting machine is equipped with big cutting room and movable T-shape work table. Therefore this machine has the ability of cutting rectangle and large specimens. Also the equipped separate type vice is very convenient for operator to clamp various heterotypic work pieces.

METALLOGRAPHY SPECIMEN GRINDING& POLISHING MACHINE Model MBP-1B Metallography specimen grinding & polishing machine is equipped with single disk and features stepless speed changing grinding and polishing. The rotating speed of grinding and polishing disk is adjustable from 50 to 1280 rpm.

The mounting press is a mechanical type machine. By turning the hand-wheel of the machine, a coupling of bevel gear is rotated to drive the screw rod which in turn pushes/pulls the lower die up and down along the mould sleeve. The thermoset plastic granules together with specimen being mounted is formed under heated conditions. During this process the pressure is self adjusted by a spring fixed inside the machine.A signal light is used to indicate the pressure level

Metallography is the study of the physical structure and components of metals, typically using microscopy.The surface of a metallographic specimen is prepared by various methods of cutting, grinding, polishing, and etching. After preparation, it is often analysed using optical or electron microscopy. Using only metallographic techniques, a skilled technician can identify alloys and predict material properties.Our BBG‐110 is Single Belt Metallography Belt Grinder. Single Belt General Purpose Grinder is used for flat Coarse grinding prior to fine grinding. The specimens to be ground in 60,80 or 120 grit after cutting or moulding operation to remove surface imperfections.

Micro Lathe machine is an automatic Lathe Machine.

Belt Grinder is suitable for flat, coarse grinding prior to fine grinding. The specimens to be ground in 60, 80 or 120 grit after cutting operation or moulding to remove surface imperfections. Useful step to remove light metallurgical damage in the specimen surface induced during cut-off operation.

Features:Perfect introduction to metal turning Small and light weight, fits anywhere Cast iron and steel construction Electric variable speed control Manual or powered lead screw feed Capacity 140 mm diameter, 250 mm between centre Variable Speed Over-Load protection Inside lead screw

ACO-110 Abrasive Cutter is rugged, sturdy and designed to cut metallurgical samples to optimal quality consistently and safely. Abrasive wheel spindle is connected with motor shaft by pulley and belt mechanism in ACO 110 where the motor is directly coupled to abrasive wheel. The movement of cutting wheel towards the specimen is applied by handle fixed with motor base pivot spindle and the cutter unit is balanced by springs for smooth downward movement.

OurACO-100Metallographic specimen cutting machine can be used to cut various metal and non-metal materials so as to get specimen and observe the metallographic or lithofacies structure.

Our ACO-110 Metallographic specimen cutting machine can be used to cut various metal and non-metal materials so as to get specimen and observe the metallographic or lithofacies structure.

Our BETACUT-100Metallographic Specimen Cutting Machine can be used to cut various metal and non-metal materials so as to get specimen and observe the metallographic or lithofacies structure. It is a kind of Manual/Automatic cutting machine and can be switched between Manual and Automatic modes as per user requirements.